The SPV "Saltwater" Series

The Saltwater Series is the ultimate in a saltwater flats fishing boat. Whether fishing the hard to get to areas where the lunkers hide or gliding inches over the oyster bars of the gulf in pursuit of redfish. The Saltwater Series comes equipped with all the necessities for the ultimate fishing experience, such as polished stainless steel rigging, lockable 7' rod box, aerated live well with bait separator, insulated cooler and Big Block Performance.

HULL

• One Piece Bottom Construction
• Non-Trip of Latest Design
• Lengths Available 16‘, 17' and 18'
• Beam 8'
• High sides and Transom for Safety
• Transom relieved 15 Degrees for Rear Wash Safety
• All Welded Aluminum Construction Bottom and Transom Marine Alloy 5086 .190
• Bulkhead and Sides Marine Alloy 5052 .125 Aluminum
• Bottom Stiffeners Equally Spaced Across Bottom
• Min. 7- 2” X 2” X ¼” T-Bar Stringers
• Mid-Ship Cross Brace
• Recessed Deck Area 36” Width
• Storage Under Bow with flush mount Lockable Access with drip rail
• 3/4 Walkaround
• Top of Deck Non-skidded for safety
• Lockable 7' Rod Box
• Aerated Live Well with Bait Separator
• Insulated Cooler
• Custom hull strip 

POLYMER

• 3/8” Polymer Bottom
• Attached with Stainless Steel Fasteners

ENGINE

• New 454 C.I.D. / 425 H.P. GM Engine
• New Holley 800 CFM Carburetor
• 12 Volt 65 Amp Alternator with Dual Belt/ Pulley System
• Electric Fuel Pump with Fuel Filter/Water Separator
• U.S.C.G. Approved Fuel Lines
• Electric Gear Reduction Starter
• Certified Marine Spark Arrestor/ with Rain Cover
• HEI Distributor
• Heavy Duty Flywheel 

REDUCTION

• Stinger Gear Reduction
• 2.38 to 1 Ratio
• Soft Drive

PROPELLER

• Adjustable pitch Composite Propeller Matched to Horse Power of Engine

SEATING

• Seating for five, Two Single Rear Operator , Triple Seat up Front
• Your Choice of Color Custom Marine Vinyl Seat Cushions and Rain Covers

RIGGING

• Stainless Steel Super Structure with 1 ¼” Engine Stand Supports
• Stainless Steel Seat Package and Cage

EQUIPMENT

• Cable Steering Attached to Top of Rudders
• Stainless Steel Flex Pipe 3”
• Stainless Steel Headers
• Stainless Steel Mufflers
• Heavy Duty Engine Cooling Aluminum Radiator
• Aluminum Coolant Expansion Tank
• U.S.C.G. Approved Radiator Hoses
• Complete Bilge System
• Dual Batteries with Battery Boxes
• Ignition Protected Battery Selector Switch
• Certified 50 Gallon Aluminum Fuel Tank with Remote Fill
• 4 Foot Air Foiled Aluminum Rudders, Foam Filled, Nylon Bushings
• Stainless Steel Rudder Rods
• Rudders Attached with Rod Ends
• Assembled with Stainless Steel Fasteners
• KC Lights Attached to Cage
• Rod Holders on Cage
• Stainless Steel Flush Mount Cleats
• Floor Board Courtesy Light

INSTRUMENTATION

• Marine Standard Wiring
• Lighted Marine Gauges
• Labeled Marine Toggle Switches
• Voltmeter
• Temperature Gauge
• Oil Pressure Gauge
• Tachometer
• Hour Meter
• Fuel Gauge
• Marine Keyed Ignition Switch
• 1- 12 Volt Marine Power Point
• Fuse Panel with Circuit Breakers
• U.S.C.G. Approved Navigational Lights

 TRAILER

• Galvanized
• Tandem Axle (3500 lbs. Per axle)
• 2” Heavy Duty Coupler
• Heavy Duty Tongue Jack with Wheel
• Heavy Duty Wench
• Easy Grease Bearings
• Carpet Side Boards
• D.O.T. Lights 

Click to see additional options here

For pricing and configuration details call our sales department at (352) 401-9070!